The 2012 Jeep Wrangler comes with a factory-installed coolant that is designed to last the lifetime of the vehicle. However, if you do need to add coolant, make sure to use only distilled water or a 50/50 mix of distilled water and ethylene glycol antifreeze. Do not use tap water, as it can contain minerals that will clog the radiator and cause overheating.
If your 2012 Jeep Wrangler is like most other vehicles on the road, it uses a coolant to help keep the engine running at its best. Coolant helps to regulate the temperature of the engine and prevents overheating. It’s important to make sure that your Jeep has the right amount of coolant, and that it’s in good condition.
Here are a few tips on how to keep your Jeep’s coolant in top shape: 1. Check the level of coolant regularly. The level should be between the “full” and “low” marks on the reservoir.
If it’s below the “low” mark, add more coolant until it reaches the “full” mark. 2. Inspect the condition of the coolant itself periodically. It should be a clear, bright green color.
If it looks rusty or murky, it needs to be replaced. 3. When adding new coolant, use only a 50/50 mix of water and antifreeze/coolant . This will help protect your engine from corrosion and freezing .
2012 Jeep Wrangler Coolant Capacity
Assuming you would like a blog post discussing the coolant capacity of the 2012 Jeep Wrangler: The 2012 Jeep Wrangler comes equipped with a 3.6-liter V6 engine and has a total coolant capacity of 12.5 quarts. This means that when you’re adding coolant, you should add no more than 12.5 quarts to avoid overfilling the system.
If your Wrangler is low on coolant, it’s important to add the correct type in order to avoid damaging the engine. The recommended coolant for the 2012 Jeep Wrangler is Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology).
What Kind of Coolant Goes in 2012 Jeep Wrangler?
Jeep Wranglers come with a standard cooling system that includes a radiator, water pump, thermostat, and engine block. The coolant you’ll need will depend on the model year of your Jeep. For 2012 models, use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula (MS-9769).
This is a long-life coolant that’s compatible with all materials used in Jeep cooling systems.
What Kind of Coolant Do Jeep Wranglers Use?
If you own a Jeep Wrangler, it’s important to know what kind of coolant to use in order to keep your engine running smoothly. There are many different types of coolant on the market, but not all of them are compatible with Jeep Wranglers. The best coolant for Jeep Wranglers is a 50/50 mix of ethylene glycol and water.
This mixture will provide the best protection for your engine, preventing corrosion and overheating.
How Do I Add Coolant to My 2012 Jeep Wrangler?
Assuming you are referring to the radiator and not the engine oil: Locate the coolant reservoir. It will be on the driver’s side of the Jeep Wrangler, and it will have a white cap with “coolant” written on it.
Remove the cap slowly in order to avoid hot coolant spraying out. Fill the reservoir until it reaches the “full” line. You can use water or a 50/50 mixture of water and antifreeze.
If you live in an area with very cold winters, you may want to use all antifreeze so your Jeep doesn’t overheat during operation. Put the cap back on tightly and start up your Jeep Wrangler to make sure everything is working properly.
What Color is Jeep Wrangler Antifreeze?
Assuming you are asking about the Jeep Wrangler model year 2018, the antifreeze is green.
Why is the JK Overheating?? 2012 Jeep Wrangle JK
Conclusion
If your 2012 Jeep Wrangler is leaking coolant, you might be wondering what kind to use to top it off. The type of coolant used in a Jeep Wrangler depends on the model year. Up until 2011, Jeep Wranglers used Dex-Cool coolant, which is an ethylene glycol based coolant.
In 2012, Jeep switched to a propylene glycol based coolant, which is less toxic and more environmentally friendly.