The 2008 Jeep Wrangler steering angle sensor is an important safety feature that helps the driver maintain control of the vehicle. This system uses sensors to measure the angle of the front wheels and sends a signal to the computer, which then adjusts the amount of power assist to the steering system. This feature can be especially helpful when driving on slippery or uneven surfaces.
If your Jeep Wrangler is from 2008 or newer, then it’s equipped with a Steering Angle Sensor (SAS). This nifty little device helps your Jeep know what angle the front wheels are turned. That way, if you start to drift off course, your Jeep can automatically correct itself and keep you going straight.
The SAS is an important safety feature, but it can also be a bit of a pain. If the SAS gets knocked out of alignment, it can cause your Jeep to veer off course unexpectedly. You may also find that your Jeep feels “floaty” or “numb” when driving on the highway.
That’s because the SAS is no longer able to make small corrections to keep you going in a straight line. If you’re having steering problems with your 2008 Jeep Wrangler, then it’s possible that the SAS is to blame. The good news is that realigning the SAS is relatively easy and doesn’t require any special tools.
Just follow these simple steps: 1) Park your Jeep on level ground and turn off the engine. Make sure that the front wheels are pointing straight ahead.
2) Locate the SAS unit behind the steering wheel (it should be close to where the steering column meets the dashboard). There are two adjustment screws on top of the unit – one for left/right adjustments and one for up/down adjustments. 3) Use a flathead screwdriver to turn each adjustment screw until the horizontal line on top of the unit lines up with zero on its corresponding scale (left/right or up/down).
4) Once both adjustment screws are in place, turn on your Jeep’s ignition but don’t start the engine yet. Slowly turn the steering wheel back and forth until you hear two clicks coming from inside the SAS unit – this indicates that it has reset itself and aligned properly with your steering system once again!
2008 Jeep Wrangler Steering Angle Sensor Location
If you’re having trouble with your 2008 Jeep Wrangler’s steering, one potential cause could be a faulty steering angle sensor. The good news is that this sensor is relatively easy to find and replace. Here’s a quick guide to help you locate and replace the steering angle sensor on your Jeep Wrangler.
The first step is to identify where the steering angle sensor is located. On most Jeeps, it will be located near the bottom of the steering column, just above the steering wheel. Once you’ve found it, disconnect the electrical connector and remove the two bolts that hold it in place.
With the old sensor removed, take a look at the new one to make sure it’s identical. If everything looks good, go ahead and install the new sensor in the reverse order of how you removed the old one. Reconnect the electrical connector and tighten down those bolts.
Now start up your Jeep and see if the problem has been resolved. If not, there may be another issue at play here so don’t hesitate to get professional help if needed.
What are the Symptoms of a Faulty Steering Angle Sensor?
If you’re having trouble with your car’s steering, it could be a problem with the steering angle sensor. This component is responsible for sending information to the car’s computer about the position of the steering wheel. If it’s not working properly, it can cause all sorts of problems.
Here are some common symptoms of a faulty steering angle sensor: The most obvious symptom is that the car will pull to one side when you’re driving straight. This is because the computer isn’t getting accurate information about the position of the wheel and thinks that you’re turning when you’re not.
As a result, it compensates by making small adjustments to keep the car going straight. Another common symptom is intermittent power steering. The power steering system relies on information from the steering angle sensor to know how much assist to give you when you turn the wheel.
If the sensor isn’t working right, then the power steering can suddenly cut out or become very weak. This can make it difficult to steer, especially at low speeds. If your check engine light comes on, there’s a good chance that it’s because of a problem with the steering angle sensor.
The code should tell you exactly what’s wrong and where to look for it. Finally, if your car seems to be wandering all over the road, even when you’re not touching the wheel, that could also be a sign of a bad steering angle sensor. Again, this has to do with incorrect information being sent to the computer about where the wheels are pointing.
How Do You Reset a Jeep Steering Angle Sensor?
The Jeep steering angle sensor, also called a yaw rate sensor, is used by the electronic stability control system to help keep your vehicle stable on the road. If the system detects that your vehicle is starting to lose traction, it will automatically apply the brakes to individual wheels and reduce engine power to help you regain control. If you’ve recently had work done on your suspension or alignment, it’s possible that the steering angle sensor needs to be reset.
This can usually be done by taking your Jeep to a dealership or service center that has the proper diagnostic equipment.
Can You Reset a Steering Angle Sensor?
Yes, you can reset a steering angle sensor. This is typically done if the sensor has become out of alignment or if there is an issue with the sensor itself. To reset the sensor, simply disconnect and reconnect the battery.
You may also need to recalibrate the sensor after resetting it.
What Happens If You Don’T Reset Steering Angle Sensor?
If you don’t reset your steering angle sensor, your car will eventually drift off course. The reason for this is that the sensor measures the angle of the front wheels and uses this information to control the electronic stability system. If the sensor isn’t reset, it won’t be able to properly track the position of the wheels and will eventually cause the car to veer off course.
C123F STEERING WHEEL POSITION SENSOR | JEEP WRANGLER 2017 | SAS
Conclusion
The 2008 Jeep Wrangler comes with a Steering Angle Sensor that is designed to help improve the vehicle’s handling. This sensor is located in the front of the vehicle, and it monitors the steering angle of the wheels. If the sensor detects that the steering angle has changed, it will automatically adjust the suspension settings to improve stability and control.