If you own a 2008 Jeep Wrangler, you may have noticed that the glove box latch is not working properly. This can be a real pain, especially if you need to access your glove box in a hurry. Luckily, there is an easy fix for this problem.
With a few simple tools, you can replace the broken latch with a new one in no time.
If you own a 2008 Jeep Wrangler, you may have noticed that the glove box latch is not working as it should. This can be a real pain, especially if you need to access something in your glove box while driving. Luckily, there is an easy fix for this problem.
All you need to do is replace the glove box latch with a new one. Replacing the glove box latch on your Jeep Wrangler is a pretty simple process. You’ll just need a few tools and about 30 minutes of your time.
First, remove the two screws that hold the glove box door in place. Then, pull the door off of the hinges and set it aside. Next, locate the old glove box latch and remove it from the housing.
To install the new latch, simply insert it into the housing and screw it in place. Then, reattach the glove box door and screw it back into place. That’s all there is to it!
With a new glove box latch in place, your Jeep Wrangler will be as good as new again!
Jeep Wrangler Glove Box Latch Replacement
If you own a Jeep Wrangler, you know that the glove box is one of the most useful storage areas in the vehicle. But what happens when the glove box latch breaks? Don’t worry, it’s an easy fix!
Here’s what you’ll need: -Phillips head screwdriver -Flat head screwdriver
-Glue (optional) First, remove the two screws that hold the glove box door in place. These are located at the top of the door.
Then, gently pull the door away from the dashboard. Be careful not to break any of the plastic tabs that connect the door to the dash. Once the door is disconnected, you’ll see a metal rod that runs through a plastic sleeve.
This is what actuates the latch when you close the glove box door. The sleeve is held in place by two small Phillips head screws. Remove these screws and carefully slide out the sleeve.
Now, take a look at how everything fits together and make note of it so you can put it back together correctly. There’s a spring inside of the sleeve that helps keep tension onthe latch so it doesn’t come undone while driving. If your new latch doesn’t come with a spring, be sure to transfer yours over.
You may also want to add some glue to help keep everything in place while reassembling (this isn’t strictly necessary). To install your new latch, simply reverse these steps! Slide inthe new sleeve and replacethe two Phillips head screws. Reconnectthe glove box door usingthe original screws (or new ones if needed) and give it a test before putting everything back together..
How Do I Fix a 2008 Jeep Wrangler Glove Box Latch
If your Jeep Wrangler’s glove box latch is not working properly, there are a few things you can do to fix it. First, check to see if the latch is simply dirty or jammed. If it is dirty, you can clean it with a cloth and some WD-40.
If the latch is jammed, you may be able to fix it by gently prying it open with a flat head screwdriver. If neither of these solutions works, the next step is to replace the glove box latch assembly. This is a relatively easy process that should only take about 15 minutes.
You will need a new glove box latch assembly (available at most auto parts stores), a Phillips head screwdriver, and a flat head screwdriver. To begin, open the hood of your Jeep and disconnect the negative battery cable. Next, locate the two screws that hold the glove box in place (one on each side).
Remove these screws and set them aside. With the screws removed, you should now be able to pull the glove box out far enough to access the back of it. Locate the three wires that connect to the back of the glove box light (one black, one white, and one green).
Disconnect these wires and set them aside. Now reach into the opening where the glove box was and locate the two clips that hold the old glove box latch in place (one on each side). Use a flat head screwdriver to gently pry these clips off so that you can removethe old latch assembly.
Once this is done, simply reverse these steps to install your newglove boxlatch assembly!
Where Can I Buy a Replacement 2008 Jeep Wrangler Glove Box Latch
If you need to replace the glove box latch on your 2008 Jeep Wrangler, you have a few different options. You can either buy a replacement from the dealership, or you can find one online from a reputable automotive parts retailer. If you decide to go with the dealership, they will likely have the exact same model of latch that came on your Jeep originally.
This is the best option if you want an OEM (original equipment manufacturer) part. However, it will probably be the most expensive option as well. If you decide to look for a replacement online, there are many different retailers that sell aftermarket parts for Jeeps.
These parts are usually less expensive than OEM parts, but they may not be an exact match for your Jeep’s original latch. It’s important to do some research and make sure that you’re getting a quality aftermarket part before making your purchase.
What is the Process for Replacing a 2008 Jeep Wrangler Glove Box Latch
If you need to replace the glove box latch in your 2008 Jeep Wrangler, there are a few things you need to know. First, the glove box is held closed by a spring-loaded catch. To open it, you simply push on the release tab.
The catch is mounted to the glove box door with two screws. Remove these screws and the catch will come right off. The replacement catch will also have two mounting holes for the screws.
Next, locate the retaining clip that holds the latch assembly in place. This clip is located on the underside of the glove box door near where the latch assembly mounts. Use a flat head screwdriver to pry up on this clip and release it from its retaining groove.
With the clip released, you can now pull out on the latch assembly and remove it from the door. The replacement assembly will easily install in its place. Be sure to engage the retaining clip before closing up everything again.
2007 Wrangler Glove Compartment Box Latch Replacement.
Conclusion
If you own a 2008 Jeep Wrangler, you may have noticed that the glove box latch is not working properly. This can be a real pain, especially if you need to access something in your glove box while driving. Luckily, there is an easy fix for this problem.
All you need to do is replace the glove box latch with a new one. This is a relatively simple process that anyone can do, and it will only take a few minutes of your time.