There are four bolts that hold the starter in place on a 1995 Jeep Wrangler. Two of these bolts are located at the top of the starter, and two are located at the bottom. The top bolts are larger than the bottom bolts, and they also have left-hand threads.
This means that you will need to turn them to the right to loosen them. The bottom bolts are standard right-hand threads.
The starter bolts on a 1995 Jeep Wrangler are located on the engine block. The number and size of the bolts will vary depending on the model of Jeep Wrangler. Most models will have four or six starter bolts.
The bolts are typically 8mm or 10mm in size.
Jeep Yj Starter Bolt Size
If you’re looking to replace the starter on your Jeep Yj, you’ll need to know what size bolt to use. The size of the bolt will depend on the model of Jeep Yj that you have. For example, early model Jeeps used a 5/16″ bolt, while later models used a 3/8″ bolt.
Be sure to check your owner’s manual or ask a mechanic before purchasing a replacement starter so that you get the correct size for your Jeep.
What Size Bolts are on a Starter?
There are a few different types and sizes of bolts that can be found on a starter. The most common type is the hex bolt, which is typically around 3/8″ in diameter. There are also 10mm and 12mm bolts used on some starters.
The size of the bolt will depend on the make and model of the starter.
Are Starter Bolts Reverse Threaded?
If you’re wondering whether starter bolts are reverse threaded, the answer is yes – they are! This is because when you’re trying to start your car, the engine’s crankshaft is spinning in the opposite direction of the starter motor. Therefore, the bolts that connect the starter motor to the engine need to be reverse-threaded so that they don’t come loose while the engine is running.
What Causes Broken Starter Bolts?
If you’re a car owner, sooner or later you’ll need to deal with a broken starter bolt. While this can be a frustrating and even dangerous problem, it’s important to understand what causes them in the first place. Only then can you take the necessary steps to prevent them from happening again.
There are actually several different things that can cause a starter bolt to break. The most common is simply age and wear-and-tear. Over time, the bolts that hold your starter in place will inevitably loosen and break.
This is especially true if you don’t regularly check and tighten them. Another common cause of broken starter bolts is corrosion. If your car is exposed to salt (from road salt or ocean water), it can speed up the corrosion process and cause the bolts to break much sooner than they otherwise would.
Finally, impact damage can also cause broken starter bolts. If your car hits something hard enough (like a curb or pothole), it can jar loose the bolts holding your starter in place. In some cases, this damage may not be immediately apparent, but over time it will weaken the bolts and make them more likely to break when put under stress.
No matter what causes your particular problem, the end result is always the same: you need to replace the broken bolt(s) as soon as possible before your car won’t start at all!
How Do You Fix a Bolt Hole in a Starter?
If you have a stripped bolt hole in your starter, there are a few ways to fix it. One way is to use a helicoil insert. This is a small metal sleeve that you insert into the stripped hole.
The helicoil will give the bolt something to grip onto, and will keep it from stripping again in the future. Another way to fix a stripped bolt hole is by using an epoxy. First, clean out the area around the hole so that the epoxy can adhere properly.
Then mix together the epoxy and apply it to the hole. Once it has dried, you can then screw in a new bolt. If neither of these methods work for you, then you may need to replace the entire starter assembly.
Replacing starter on 95 Jeep Wrangler
Conclusion
If your Jeep Wrangler won’t start, it could be a problem with the starter bolts. These bolts can loosen over time and cause the starter to fail. You can replace the starter bolts yourself with a few tools and some patience.
Follow these steps to do the job right.