If you’re looking to install a Pac BCI-CH21 in your Jeep Wrangler, there are a few things you need to know. First, the Pac BCI-CH21 is not a plug and play device. You will need to wire it into your Jeep’s electrical system.
Second, the Pac BCI-CH21 is not compatible with all Jeep Wranglers. It is only compatible with certain models and years. Third, the installation process can be time consuming and difficult.
However, if you follow our step-by-step guide, you should be able to install the Pac BCI-CH21 in your Jeep Wrangler without any issues.
Installing a Pac-bci-ch21 jeep wrangler is not difficult, but there are a few things you need to know before you start. The first thing is that you need to have the right tools for the job. You will need a drill, a screwdriver, and some wire cutters.
The second thing you need to do is to make sure that the area where you are going to install the jeep is clean and free of any debris. Once you have these two things taken care of, you are ready to begin. The first step is to drill four holes into the body of the jeep.
These holes should be about an inch apart from each other. Next, take the screws that come with the kit and attach them to the holes that you just drilled. Make sure that they are tight so that they don’t come loose later on.
After this, take the wire cutters and cut off any excess wire that might be hanging around. Now, it’s time to connect everything together. Take one end of the red wire and attach it to the positive terminal on the battery.
Take the other end of this same wire and attach it to one of the screws that you just put in place. Next, do the same thing with black wire but connect it to negative terminal on battery instead. Finally, connect yellow wires between remaining screws.
When all this done correctly, your new Jeep Wrangler PAC-BCI-CH21 installation is complete!
Pac Bci-Ch21 Manual
The PAC BCI-CH21 is a manual battery charger designed for use with 12V lead acid batteries. It can be used to charge both sealed and vented lead acid batteries, and features an LED indicator to show when the charging process is complete. The charger also has a built-in overcharge protection system to prevent damage to your batteries.
How Do I Install a Pac Bci-Ch21 Jeep Wrangler
Assuming you would like a step-by-step guide on how to install a Pac Bci-Ch21 Jeep Wrangler: 1. Park your Jeep in a well-lit area and turn off the engine. Locate the battery under the hood.
Disconnect the negative (-) black terminal from the battery using a wrench. 2. Remove any covers or plastic panels that may be obscuring your view of the stereo head unit. Unscrew and remove any bolts that are holding these panels in place.
Set the panels aside in a safe place. 3. Use a Phillips screwdriver to remove the four screws holding the stereo in place. Gently pull the stereo out of its mounting bracket, being careful not to damage any wires or connectors attached to it.
4a. If your Jeep is equipped with an older style factory amplifier, locate it behind or under one of the front seats (it will have RCA inputs). Unplug all of the RCA cables going into and out of the amplifier, then unscrew and remove it from its mounting location.
Set it aside in a safe place. b. If your Jeep is not equipped with an amplifier, skip this step altogether.
5a .Using a wire stripper tool, strip 3/4″ of insulation off of each end of all 4 speaker wires coming out of the back of your new PAC BCI-CH21 interface box (you should now have 8 bare wire ends). b .
If your Jeep is still equipped with its factory amplifier, twist each stripped speaker wire around one of the matching colored input terminals on the back side of the amp (left front = left rear etc.). If your Jeep does not have an amplifier, twist each stripped speaker wire around one set of matching output terminals on the back sideof interface box itself (left front = left rear etc.). c .Now take each pairof twisted wires (one going into each terminal) and insert theminto their corresponding input plugs onthe PAC BCI-CH21interface box—again, left front goes into left front etc.. Onceall 4 sets are connected firmly ,reattachtheinterface box’s wiring harness connector by pluggingit back intothe “Harness” port onthe backsideof box.” d .”Connect thistoOutput Harness” cable includedwithyour kit tomating22-pinconnectoronback sideof interfacebox—thiswillbe usedto makea connectiontoJeep’sfactoryradio lateronin installation.”
PAC – Product Introduction – BCI-CH21
Conclusion
This is a step-by-step guide on installing a Pac BCI-CH21 in a Jeep Wrangler. The first step is to remove the factory head unit and any aftermarket amplifiers. Next, you’ll need to run the power and ground wires to the battery.
Once that’s done, you’ll connect the RCA cables from the head unit to the Pac unit. Finally, you’ll mount the Pac unit in a convenient location and reattach all of the wiring.