Jeep Wrangler Quick Release Door Pins

If you own a Jeep Wrangler, then you know that one of the most annoying things can be having to remove the doors. Well, there is a way to make it a lot easier and that is by installing quick release door pins. Quick release door pins are great because they allow you to take the doors off in just a few seconds.

They are very easy to install and they will make your life a lot easier.

If you own a Jeep Wrangler, you know that one of the best features is the ability to remove the doors. This not only gives you a great opportunity to enjoy some fresh air and sunshine, but it also makes cleaning and washing your Jeep much easier. The only downside to removing your doors is that it can be a bit of a pain to put them back on, especially if you don’t have quick release door pins.

Fortunately, there are a number of companies that make quick release door pins specifically for Jeep Wranglers. These pins make it easy to remove and replace your doors in just a few minutes. If you’re looking for an easy way to improve your Jeep Wrangler experience, quick release door pins are definitely worth considering.

Jeep Wrangler Door Hinge Pin Replacement

If your Jeep Wrangler’s door hinge pins are worn out, you’ll need to replace them. Here’s a step-by-step guide on how to do it: 1. Start by removing the door from the Jeep.

This will make the replacement process much easier. 2. Next, use a drill to remove the old hinge pins. Be careful not to damage the door while doing this.

3. Once the old hinge pins are out, insert the new ones in their place. Make sure they’re snug and secure before moving on.

How Do You Take the Pins Out of a Jeep Door Hinge?

Assuming you mean the hinge pins that attach the door to the jeep body: There are a few ways to remove hinge pins, depending on what tools you have available. The easiest way is to use a drill.

First, drill a hole in the pin near the head. Then, insert a nail or other small metal rod into the hole and hit it with a hammer until the pin pops out. You may need to wiggle the door back and forth while doing this to get the pin started moving.

If you don’t have a drill, you can try using a screwdriver and hammer. First, find a spot on the pin where you can get good leverage with the screwdriver. Then, hitting the handle of the screwdriver with a hammer, attempt to drive the pin out from that spot.

It may take some time and patience to get both pins out this way. Once both pins are removed, your door should be able to be lifted off easily.

What Size Torx is a Jeep Door Hinge?

If you have a Jeep, chances are you know that the door hinges are a little different than those on other vehicles. The main difference is the size of the Torx screws that hold them in place. So, what size Torx is a Jeep door hinge?

The answer may surprise you – there is no one-size-fits-all answer to this question. The size of the Torx screws can vary depending on the year and model of your Jeep. For example, early model Jeeps (prior to 1987) used T40 screws, while later models use T50 screws.

So, if you’re not sure what size Torx screw is used on your Jeep’s door hinges, the best thing to do is to consult your owner’s manual or ask a dealership technician. They’ll be able to quickly tell you which size screw you need.

What is the Easiest Way to Take off a Jeep Door?

Assuming you are referring to a full-sized jeep door and not a Jeep Wrangler door: The easiest way to take off a jeep door is to disconnect the hinges. There are typically three bolts on each hinge – two at the bottom of the door and one at the top.

Once these are removed, the door can be lifted off.

What Size Socket Do I Need to Remove Jeep Doors?

If you need to remove the doors on your Jeep, you will need a socket that is 7/8 inches in size. This is the standard size for most door hinges. You may also need a Phillips head screwdriver to remove the screws that hold the door panel in place.

American Outlaw EZ-On Door Hinge Pin Guides for Jeep Wrangler JK or TJ

Conclusion

If you’ve ever had to remove your Jeep Wrangler doors, you know it can be a pain. The door pins are held in place by spring-loaded clips, and they’re a pain to get out. But there’s a quick and easy way to do it.

All you need is a flat head screwdriver and a pair of needle nose pliers. First, use the screwdriver to pry up on the pin clip. You may need to wiggle it a bit to get it started.

Once the clip is loose, use the pliers to pull it out completely. Then just pull on the door pin and it will come right out. To put the doors back on, just reverse the process.

Put the door pin in place and then use the pliers to put the clip back on. Make sure that the clip is fully seated before letting go of it.