If you’re a Jeep Wrangler owner, you may have noticed that the 2018 model has a new feature called “Neutral Override.” This allows the vehicle to be started in Neutral without the need for the clutch pedal to be depressed. Here’s how it works:
With the key in the ON/RUN position and the transmission in NEUTRAL, depressing the brake pedal will allow the engine to start. Once started, releasing the brake pedal will engage the transmission and allow normal operation of the vehicle. This new feature is designed for those who frequently drive in off-road or low-traction situations where starting in first gear with a traditional clutch pedal can be difficult.
It’s also helpful if you find yourself stuck on a hill or in mud and need to get moving again without having to worry about engaging the clutch.
If you’re like most Jeep Wrangler owners, you love to take your vehicle off-road. But what happens when you come across a stream or river that’s too deep to cross without getting wet? That’s where the 2018 Jeep Wrangler Neutral Override comes in handy.
This feature allows you to shift your Jeep into neutral while keeping your foot on the brake. This prevents your engine from stalling if you happen to get water in the intake. And best of all, it’s completely free!
So be sure to take advantage of this great feature next time you’re out exploring nature.
Jeep Wrangler Jk Shift Lock Release
If your Jeep Wrangler JK is equipped with an automatic transmission, then you’re probably familiar with the shift lock release. This feature prevents the vehicle from being shifted out of park unless the brake pedal is depressed. However, there may come a time when you need to override the shift lock release in order to move your Jeep.
Here’s a quick guide on how to do just that: 1. Locate the shift lock release button. This is typically located on the center console near the shifter knob.
2. Press and hold the shift lock release button while you depress the brake pedal and attempt to shift out of park. 3. If successful, your Jeep should now be in gear and ready to go! Keep in mind that overriding the shift lock release should only be done in emergency situations.
If you find yourself needing to do this on a regular basis, then it’s time to have your transmission checked by a professional.
How Do You Put a 2018 Jeep Wrangler in Neutral?
If your Jeep Wrangler is equipped with an automatic transmission, you can put it in neutral by depressing the brake pedal and then shifting the transmission into the “N” position. If your Jeep has a manual transmission, you can put it in neutral by depressing the clutch pedal and then moving the shifter into the neutral position. To shift out of neutral, simply depress the clutch (if manual) or brake (if automatic) and move the shifter into the desired gear.
How Do I Put My Jeep Wrangler in Neutral With Dead Battery?
If your Jeep Wrangler has a dead battery, you can put it in neutral by following these steps: 1. Disconnect the negative terminal of the battery. 2. Locate the transmission shifter cable at the base of the shifter Lever.
3. Using a flat head screwdriver, depress the retainer clip that secures the shifter cable to the transmission lever. 4. With the retainer clip depressed, slide the shifter cable off of the transmission lever. 5. Insert a small flat head screwdriver intothe slot in the side ofthe shifter knob and rotate counter clockwise untilthe knob pops offofthe shaft.
6. With The knob removed, pull up on The white plastic sleeve that is surroundingThe shift rod untilit slides outofThe hole in The center console trim panel (you may have to wiggle it backand forthto get it started). This will expose The end ofThe shift rod with a small metal retaining clip holding It in place insideofa plastic housing (as seen below). Remove this metal retaining clip by depressing one side with a small flatheadscrewdriver and slidingIt offTo The side (it helps If you can get something underIt to keep It from falling Into The abyss never to be seen again).
7With The metal retaining clip removed, carefully pull up onThe shift rod untilThe plastic housing comes outofThe hole InThe center console trim panel enough forYou to grab holdofIt (be sure not to lose any Of The small parts inside Of The housing such as springs and detents). Now would be agood time To make sure everything Is still where It’s supposedto be Insidethe housing before proceeding any further!
How Do You Put a Jeep Wrangler in Neutral on a Tow?
If you’re planning on towing your Jeep Wrangler, it’s important to know how to put it in neutral. Follow these steps and you’ll be ready to go in no time: 1. Park your Jeep on a level surface and set the parking brake.
2. Start the engine and shift into first gear. 3. Release the clutch pedal slowly until you feel the engine start to engage. 4. Continue depressing the clutch pedal and push down on the shifter until it reaches the second detent from the bottom.
This is neutral. 5. Hold the shifter in place and release the clutch pedal slowly until you hear or feel a click. This means that your Jeep is now in neutral and ready to be towed!
How Do You Put a 2015 Jeep Wrangler in Neutral With a Dead Battery?
If your Jeep Wrangler’s battery is dead, you can put it in neutral by doing the following: 1. Disconnect the negative cable from the battery. 2. Locate the transmission control module (TCM) – it will be on the driver’s side of the transmission, near the battery.
3. Using a small screwdriver or other tool, press and hold the “program” button on the TCM while you turn on the ignition switch. 4. Continue to hold the button until the lights on the TCM start flashing (this will take about 5 seconds). 5. Release the button and turn off the ignition switch.
2018 and newer Jeep Wrangler (JL) and Gladiator (JT) Park Override
Conclusion
If you’re ever driving a Jeep Wrangler and need to override the neutral safety switch, here’s how. First, disconnect the battery. Next, locate the switch on the transmission.
It’s usually located on the driver’s side near the shifter. Once you’ve found it, use a flathead screwdriver to pry it up. This will allow you to engage the override and put your Jeep into gear.