The 2012 Jeep Wrangler comes with a standard steering angle sensor. This sensor is used to monitor the steering angle and provide feedback to the driver. The Jeep Wrangler has a variety of different steering angles that can be set, and the steering angle sensor helps to keep track of these angles.
This feedback can be used to help the driver maintain control of the vehicle, and it can also be used to help diagnose problems with the steering system.
If your Jeep Wrangler is having issues with the steering angle sensor, it’s important to get it fixed as soon as possible. This sensor helps to keep your Jeep stable and on course while driving. If it’s not working properly, it can cause your Jeep to veer off course or even tip over.
There are a few signs that you may notice if your steering angle sensor is going bad. The most common is the “death wobble.” This is when your Jeep starts to shake violently at high speeds, making it difficult to control.
If you notice this happening, slow down and get your Jeep checked out as soon as possible. Another sign of a bad steering angle sensor is if your Jeep seems to wander from side to side while driving. This can be extremely dangerous, so again, it’s important to get it fixed right away.
If you’re having any issues with your steering angle sensor, take your Jeep to a qualified mechanic or dealership for service. They’ll be able to diagnose the problem and get it fixed quickly so you can get back on the road safely.
Jeep Wrangler Steering Angle Sensor Reset
If your Jeep Wrangler is equipped with electronic stability control, you may need to reset the steering angle sensor from time to time. This sensor is what tells the ESC system how far the wheels are turned, and if it gets out of alignment, the ESC system can’t work properly. Fortunately, resetting the steering angle sensor is a pretty easy process.
Here’s how to do it: 1. Start by turning on the ignition, but don’t start the engine. 2. Press and hold the ESP button (it’s usually located on the dash somewhere) for about 5 seconds.
3. You should see a message on the dash that says “ESP Off.” 4. Now turn off the ignition and restart the engine. The ESP system should now be reset and working properly again.
How Do You Reset the Steering Angle Sensor on a Jeep Wrangler?
If you’re like most Jeep Wrangler owners, you probably don’t think much about your vehicle’s steering angle sensor. But if it starts to act up, it can be a real pain. Fortunately, resetting the steering angle sensor is a relatively simple process that anyone can do at home with the right tools.
First, you’ll need to find the steering angle sensor. It’s located on the front suspension near the wheels. If you’re not sure where it is, consult your Wrangler’s owner’s manual or look for it online.
Once you’ve found it, disconnect the negative battery terminal to prevent any electrical damage while you work. Next, use a wrench or socket to remove the bolts holding the steering angle sensor in place. Be careful not to damage any of the wires attached to the sensor.
Finally, reinstall the sensor and reconnect the negative battery terminal. That’s all there is to it!
What Happens When Steering Angle Sensor Goes Out?
A steering angle sensor is a vital part of a car’s electronic stability control (ESC) system. The sensor measures the angle of the steering wheel and sends this information to the ESC computer. If the computer detects that the vehicle is turning more than desired, it will automatically apply the brakes to one or more wheels to help stabilize the vehicle.
If your car’s ESC system is not working properly, it could be due to a faulty steering angle sensor. A bad sensor can cause the ESC system to malfunction, which can lead to loss of control of the vehicle during turns or sudden lane changes. In extreme cases, a failed steering angle sensor can cause a complete loss of power steering assist.
If you suspect that your car’s steering angle sensor is failing, take it to a mechanic as soon as possible for diagnosis and repair.
Where is the Steering Angle Sensor Located?
The steering angle sensor is located on the steering column, just behind the steering wheel. It is a small, black box with wires running to it from the back of the steering wheel. The sensor itself is mounted on a bracket that is bolted to the bottom of the steering column.
Can You Reset a Steering Angle Sensor?
Yes, you can reset a steering angle sensor. The process is relatively simple and only requires a few tools. First, you’ll need to disconnect the battery.
Next, locate the steering angle sensor and unplug it from the wiring harness. Finally, use a small screwdriver to remove the two screws that hold the sensor in place. With the screws removed, you can now pull the sensor out and reset it according to your vehicle’s specifications.
C123F STEERING WHEEL POSITION SENSOR | JEEP WRANGLER 2017 | SAS
Conclusion
If your Jeep Wrangler is having trouble steering, it might be due to a faulty steering angle sensor. This part is responsible for sending signals to the computer that tell it how far the steering wheel is turned. If it’s not working properly, the computer can’t make the necessary adjustments to keep the vehicle going straight.
Replacing the sensor is a pretty simple process and shouldn’t take more than an hour or so.