The 2012 Jeep Wrangler has a new gear shift light that is designed to help drivers know when to shift gears. The light is located on the instrument panel and will illuminate when the vehicle is in the correct gear for the current speed. This is a great feature for those who are new to driving a manual transmission or for those who simply want to be more aware of when to shift gears.
The light will also come in handy when driving in inclement weather or on rough terrain, as it can be difficult to see the traditional shifter in these conditions.
If your Jeep Wrangler is like most, it has a gear shift light that comes on when the vehicle is shifted into gear. This light is designed to let you know that the engine is running and ready to go. However, if this light stays on after the engine is turned off, it may indicate a problem with your Jeep’s electrical system.
If you notice that the gear shift light in your Jeep Wrangler stays on even after you’ve turned off the engine, check the battery first. If the battery is dead, it may be causing the light to stay on. If the battery isn’t the problem, there may be an issue with a fuse or circuit breaker.
Check these next and see if they need to be replaced or reset. If you can’t find anything wrong with the electrical system, take your Jeep to a mechanic for further diagnosis. There could be another reason why the gear shift light is staying on and it’s best to have a professional take a look at it just in case.
Jeep Wrangler Shift Indicator Light
A shift indicator light is a small, but important, part of your Jeep Wrangler. This light tells you when to shift gears, and is usually located on the instrument panel near the speedometer. If this light is not working, it can be very difficult to drive your Jeep properly.
There are a few things that can cause your shift indicator light to stop working. One possibility is a blown fuse; if this is the case, simply replace the fuse and see if that fixes the problem. Another possibility is a loose wire; if you suspect this might be the issue, check all of the connections to make sure they’re tight.
Finally, it’s also possible that the light itself has burned out; in this case, you’ll need to replace the entire unit. If your shift indicator light isn’t working properly, don’t hesitate to take it to a qualified mechanic for diagnosis and repair. In most cases, these issues are fairly simple and easy to fix – but driving without a functioning shift indicator light can be extremely dangerous!
Why Won’T My Gear Shift Light Up?
If your gear shift light is not lighting up, there are a few potential causes. First, check to see if the bulbs are burned out. If they are, simply replace them with new ones.
If the bulbs are not burned out, then the issue may be with the wiring. Check to see if there are any loose or damaged wires that could be causing the problem. If you find any, repair or replace them as needed.
Finally, if neither of these solutions solve the problem, then it is likely an issue with the shifter itself and will need to be replaced.
How Do You Remove a Jeep Gear Shift?
Removing a Jeep gear shift is not a difficult task, but there are a few things that you need to be aware of before starting. The first thing to do is to disconnect the battery so that you don’t accidentally engage the starter while working on the Jeep. Once the battery is disconnected, locate the three bolts that hold the shifter in place.
These bolts are located at the base of the shifter and can be removed with a socket wrench or an open-ended wrench. With the bolts removed, gently pull up on the shifter until it comes free from its housing. You may need to wiggle it a bit to get it started, but it should come out relatively easily.
There are two O-rings located on either side of where the shifter was seated; make sure not to lose these as they will need to be replaced when reinstalling the shifter. With the shifter removed, take a look at how it is mounted in its housing. There are two metal retaining clips that hold it in place; simply depress these clips and slide them out of their corresponding slots in order to remove them.
With both retaining clips removed, you should now be able to slide the entire shift assembly out of its housing for further disassembly, cleaning or inspection as needed.
How to Easily Fix a Jeep Gear Shifter Backlight
Conclusion
If you own a 2012 Jeep Wrangler, you may have noticed that the gear shift light is dim. This is a common problem and there are several easy solutions. First, try replacing the bulbs.
If that doesn’t work, then check the fuse box for a blown fuse. Finally, if neither of those solutions works, you can always take it to a mechanic to have them take a look.