The 2012 Jeep Wrangler comes with a new engine coolant. This improved coolant will help keep your engine running cooler and improve fuel economy. The new coolant is also more environmentally friendly and will not harm the ozone layer.
If you own a 2012 Jeep Wrangler, it’s important to keep an eye on your engine coolant levels. If the coolant gets too low, it can cause engine damage. Here are some tips for checking and adding coolant to your Wrangler:
1. Check the coolant level in the radiator using the dipstick. The radiator should be filled to the “full” line. If it’s not, add coolant until it reaches that level.
2. You can also check the engine coolant level by looking at the overflow tank next to the radiator. The fluid level in this tank should be between the “low” and “full” lines. If it’s below the “low” line, add coolant until it reaches that point.
3. When adding coolant, make sure to use a 50/50 mixture of water and antifreeze. This will help protect your engine from freezing in cold weather or overheating in hot weather conditions. 4 .
If you notice any leaks in your cooling system, have them repaired as soon as possible so that your engine doesn’t run low oncoolant again .
2012 Jeep Wrangler Coolant Capacity
Assuming you would like a blog post discussing the 2012 Jeep Wrangler’s coolant capacity: The 2012 Jeep Wrangler comes with a 3.6L V6 engine and has a coolant capacity of 12.5 quarts. The Jeep Wrangler is known for its off-road capabilities, but it’s also equipped with some impressive safety features.
In addition to its standard front and side airbags, the Wrangler comes with electronic stability control and Trailer Sway Control.
What Kind of Coolant Goes in 2012 Jeep Wrangler?
The recommended coolant for a 2012 Jeep Wrangler is Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula. This long-life coolant provides protection against corrosion and helps to prevent the formation of scale and deposits in the cooling system.
What Type of Coolant Does a Jeep Wrangler Take?
If you own a Jeep Wrangler, it’s important to know what type of coolant it takes. The engine in your Wrangler is designed to run at a high temperature, so it needs a coolant that can withstand high temperatures without freezing or boiling over. That’s why Jeep Wranglers take Dexcool coolant.
Dexcool is an extended-life coolant that contains organic acids. These acids help to prevent corrosion and scale build-up in the cooling system. Dexcool also has a higher boiling point and lower freezing point than traditional coolants, so it can better protect your engine in extreme conditions.
To keep your Jeep Wrangler running properly, be sure to check the level of Dexcool in the radiator on a regular basis. If you notice the level is low, add more Dexcool until it reaches the “full” line on the radiator cap. You should also have your cooling system flushed and refilled with fresh Dexcool every 50,000 miles or five years, whichever comes first.
Do Jeeps Require Special Coolant?
No, jeeps do not require special coolant. In fact, most jeeps will use the standard green antifreeze/coolant that is found at auto parts stores. The only time you may need to use a different color coolant is if your Jeep has an older engine and it requires red coolant.
How Do I Add Coolant to My 2012 Jeep Wrangler?
Assuming you are talking about the radiator and not the engine oil: The 2012 Jeep Wrangler comes with a 2.4-liter four-cylinder engine. It has a cooling system that uses a 50/50 mix of antifreeze and water.
You can buy this premixed, or you can mix it yourself. The recommended coolant for the Jeep Wrangler is Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula (part number 68046989AA). This is available from your local Jeep dealership or online.
To add coolant to the radiator, first make sure the engine is cool. Then, open the hood and locate the radiator cap on the passenger side of the engine compartment. Remove the cap and slowly pour in the coolant until it reaches just below the level of the fill neck.
Replace the radiator cap and start the engine. Let it idle for a few minutes, then turn it off and check under the hood to make sure there are no leaks.
How to Check Engine Coolant 06-18 Jeep Wrangler
Conclusion
The 2012 Jeep Wrangler comes with a new, more powerful engine. The 3.6-liter V6 produces 285 horsepower and 260 lb-ft of torque. It’s mated to a five-speed automatic transmission.
The Wrangler is also available with a six-speed manual transmission. The Wrangler has always been known for its off-road capability, and the 2012 model is no different. It features four-wheel drive with low range and a two-speed transfer case.
The suspension has been beefed up as well, with thicker sway bars and shocks that are tuned for off-road use. Despite all of this capability, the Wrangler still gets decent fuel economy. The EPA rates it at 17 mpg in the city and 21 mpg on the highway with the automatic transmission (16/20 mpg with the manual).