If you own a 2008 Jeep Wrangler, then you know that the spare tire is mounted on the back of the vehicle. This can make it difficult to access when you need it. However, there is a way to mount the spare tire on the front of the vehicle.
This will give you easy access to it and will also keep the weight evenly distributed.
If you own a 2008 Jeep Wrangler, then you know that the spare tire is mounted on the back of the vehicle. This can be a problem when trying to park in tight spaces, or when backing up into a garage. Luckily, there is an easy way to fix this problem.
All you need to do is remove the two bolts that hold the spare tire in place. Once these are removed, you can simply slide the spare tire off of the mount and store it inside your Jeep. This will give you much more clearance when parking or backing up, and it will also keep your spare tire from getting damaged.
If you ever need to use your spare tire, simply put it back on the mount and tighten down the bolts. It’s really that simple! So if you’re tired of struggling with your 2008 Jeep Wrangler’s spare tire mount, give this method a try.
Jeep Wrangler Spare Tire Carrier Replacement
If you own a Jeep Wrangler, sooner or later you’ll have to replace the spare tire carrier. The factory original equipment carrier is made of plastic and is prone to breaking. There are many aftermarket carriers available, but most are also made of plastic.
The best replacement carrier is made of steel. The first step in replacing your spare tire carrier is to remove the old one. This can be done by removing the two bolts that hold it in place.
Once the old carrier is off, you can install the new one in its place. When choosing a replacement spare tire carrier, make sure to get one that matches the size of your tires. You should also buy a carrier that comes with all necessary hardware for installation.
This will make the job much easier.
What is the 2008 Jeep Wrangler Spare Tire Mount
The 2008 Jeep Wrangler Spare Tire Mount is a device that is used to secure the spare tire on the back of the jeep. It is made up of two parts, the base plate which attaches to the jeep and the mount itself which holds the spare tire in place. The base plate is made from steel and has four mounting holes that are used to attach it to the jeep.
The mount is made from aluminum and has three set screws that are used to secure it to the base plate. The whole assembly is then bolted onto the back of the jeep using four bolts.
Where is the 2008 Jeep Wrangler Spare Tire Mount Located
Assuming you are talking about a 2008 Jeep Wrangler JK Unlimited, the spare tire is located underneath the vehicle. There is a access panel on the driver’s side that you can remove to get to the spare tire.
How Do I Remove the 2008 Jeep Wrangler Spare Tire Mount
Assuming you are referring to the spare tire from the vehicle: The 2008 Jeep Wrangler has a spare tire mount that is located on the rear of the vehicle. In order to remove it, first locate the two bolts that secure the mount to the vehicle.
These bolts are typically located near the bottom of the mount. Once you have found them, use a wrench or socket to loosen and remove them. With the bolts removed, you should now be able to pull the spare tire mount off of the vehicle.
How Do I Install the 2008 Jeep Wrangler Spare Tire Mount
Assuming you have the necessary tools and parts, installing a spare tire mount on a 2008 Jeep Wrangler is relatively straightforward. Here are the steps you’ll need to take: 1. Park your Jeep on level ground and engage the parking brake.
Loosen the lug nuts on the wheel that will be receiving the spare tire mount using a lug wrench. Do not remove them entirely at this point. 2. Raise the Jeep up off the ground using a jack, and then support it with jack stands placed under the frame for safety.
With the Jeep still raised, finish removing the lug nuts and set them aside. 3. Remove the wheel from the axle by pulling it straight outwards. Set it aside with the other removed parts.
4. Locate the two bolts holdingthe spare tire mount tothe underside ofthe jeep body;one bolt will be located nearthe center ofthe mount, whilethe other will betowards theeast or west side (dependingon which sideoftherail yourjack is positioned).Using an appropriate socket or wrench, loosenand removethese boltsbutdoremovethem completelyatthis time;you’ll onlyneedto loosen themenoughso thatyou canswivelthemoutofthe way wheninstallingthenewmounting bracket lateron in these instructions..With thoseboltsloosenedor removed, you cannow gentlyremovethespare tirMount from itspositionunderneathyourJeep’sbody panelingbypullingitdownand out untilit clearsallobstacles(suchaswiring harnessesor brake linesinits path).
Now would alsobea good timeto inspectthismountfor any signsof wear orotherdamagebeforeproceedingwith installationofanewmount.. If everythinglooksokay,set thistiremountasidefor now -you won’tneeditagainuntilyou’re readyto re-installyourspare tire atthatsame spotlateron!
Atthis pointinthe process, whatyou shouldhaveis an empty spaceunderneathyourJeep’sbody wherethelugnutscanbeclearly seenand accessedfromabove(since we’veremovedthespare tirMount), as well as twolargeopenings inthesidesofthe tubularframe rails wherethose2 mountingboltswerepreviouslylocated.. These openholeswill serveasthe attachmentpointsforthenewspare tirMountthat we’ll beinstallingin just afew minutes.
.5.. Witheverythingpreppedand readyto go, it’snow time to installthenewspare tirMountonto your2008JeepWrangler! Beginbyplacingthenewmountinto position so thatthelugnutsaresittinginside their designatedopeningsatthetop ofthemounting bracket- onceyoudothat, holdithe newmount securelyin place while aligning those2 openholesonthesidesoftubularframe withthose 2 largemountingboltsthathavebeenpreviouslyloosened/removedearlier in these instructions… Once aligned correctly,. simply startthreadingeachofthemountingboltsthroughtheir respectivesidesofthe tubularframe rail untilthey protrude throughtheopeningonthesamesideofthene wSparetir Mount (from where they wereloosened/removed earlier).
The 3 Best Jeep Wrangler Tub Mounted Tire Carriers For 2007 – 2017 JK
Conclusion
If you own a 2008 Jeep Wrangler, you may have noticed that the spare tire mount is in a different location than it was on previous model years. This change was made to provide better clearance for the rear cargo area. However, it can be difficult to reach the spare tire when it’s mounted on the side of the vehicle.
There are a few aftermarket products that can make accessing your spare tire easier. One option is a swing-away spare tire carrier. This type of carrier mounts to the frame of your Jeep and allows you to swing the spare tire out away from the vehicle.
This makes it much easier to get to, especially if you have larger tires mounted on your Jeep. Another option is a rear-mounted spare tire carrier. This Carrier bolts onto the back of your Jeep and gives you easy access to the spare tire while still providing plenty of clearance for rear cargo.
Whichever type of carrier you choose, make sure it’s rated for use with your specificJeep model year and tiresize.